Skip to main content

Pay attention to antifreeze and tires in car maintenance in autumn and winter

It has become cold in a blink of an eye today. People are more likely to catch colds and get sick during the season. The same is true for cars. If you don’t take care of them well, you are also prone to problems of this or that kind. Do you know how to maintain your car during the season?
The face of a car, the face of a person, and the maintenance of a car is very important. However, during the interview, the reporter found that many car owners would hand over all their cars to the 4S shop for maintenance, and other drivers would only perform some simple inspections on the car. As for the temperature drop, what should the car do? Everyone can think of replacing the antifreeze, but it's just two words—I don't understand.
Antifreeze is a coolant with antifreeze function, which can prevent the coolant from freezing during winter parking, expanding the radiator and freezing the engine block. Wang Shiguo reminded that two colors of antifreeze cannot be mixed, let alone use water instead of antifreeze. Moreover, the service life of antifreeze is generally two years, and it must be replaced when it expires, otherwise it will cause corrosion to the vehicle’s engine and water tank. In addition, as the temperature drops, the rubber of the tires tends to become hard and brittle, and there may be air leaks or even tire punctures, so you should always check the tires of your car.
Antifreeze and tires are all ready, can you drive on the road, don't worry, don't forget to warm up the car before leaving the car.
At this time, the vehicle has not reached the optimal state, so the speed should be kept below 50 kilometers per hour. When the water temperature gauge reaches about 90 degrees normally and the engine speed is between 500 and 800 rpm, we can drive normally.

Link to this article:Pay attention to antifreeze and tires in car maintenance in autumn and winter

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.:Cnc Machining,Thank

Comments

Popular posts from this blog

What are the characteristics of the CNC turning process?

What are the characteristics of the CNC turning process? Turning is a method of cutting the workpiece on the lathe by rotating the workpiece relative to the tool. Turning is the most basic and common cutting processing method. Most workpieces with revolving surfaces can be processed by turning methods, such as inner and outer cylindrical surfaces, inner and outer conical surfaces, end surfaces, grooves, threads, and rotary forming surfaces. Common lathes can be divided into horizontal lathes, floor lathes, vertical lathes, turret lathes and profiling lathes, and most of them are horizontal lathes.

The Influence of CNC Turning and Milling Machining on Turning Efficiency

The cutting efficiency of CNC lathes will be affected by human factors, environmental factors and the machine tool itself. Let's talk about the influence of cutting amount and cutting tools on CNC lathe processing among many factors.   Reasonable cutting amount can improve the efficiency of CNC lathe. When the   laser  cutting  speed is increased by 10 times and the feed rate is increased by 20 times, far beyond the traditional cutting forbidden zone, the cutting mechanism has undergone a fundamental change.   The result of CNC turning  and milling combined processing is: the metal removal rate per unit power is increased by 30% to 40%, the cutting force is reduced by 30%, the cutting life of the tool is increased by 70%, and the cutting left on the workpiece is greatly reduced. Heat, cutting vibration almost disappeared; cutting processing has taken an essential leap. According to the current situation of CNC lathes, increase the feed per tooth, improve pr...

Machining and welding process notes for TC4 titanium alloy parts

Common welding methods for titanium and titanium alloys are as follows: Argon arc welding, submerged arc welding, vacuum electron beam welding, etc. Tungsten argon arc welding is used for thicknesses of 3 mm or less, and argon arc welding is done for 3 mm or more. The purity of argon is over 99.99%, and the content of air and water vapor in argon is strictly controlled. Currently, for TC4 titanium alloys, argon arc welding, plasma arc welding are often used for welding, but both methods need to be filled with welding material. Limitations on shield gas, purity and effectiveness increase the oxygen content of the joint, reduce its strength and increase its post-weld deformation. Electron beam welding and laser beam welding are used. The following is a description of precision welding and precautions for TC4 titanium alloy. 1. Weld hole problem Table of Contents 1. Weld hole problem 2, internal quality of welded part 3. Weld depth and its variation 4, j...