Skip to main content

The amount of wear between the mating parts is very small

In the process of highway construction, a large number of construction machinery and construction machinery combinations are required. Due to the gradual deterioration of their technical conditions during use, the engine power decreases, fuel consumption increases, exhaust gas exceeds the standard, transmission component gaps increase, and operating mechanisms do not work well. An error occurs in the working device. This is mainly due to the wear of the parts, the structure of the parts, the processing quality of the materials, the working conditions (climate and construction environment), the quality of the fuel and lubricating materials, the reasonable degree of use, the operation methods in the construction, the configuration of the machinery, and technical maintenance Caused by repair quality, etc., we will analyze separately below. Wear and damage of construction machinery parts During the use of the machinery, wear occurs due to the friction between the parts. Under normal circumstances, the wear process of parts is divided into D stages. **The stage is the running-in stage. The surface of the processed parts is rougher before running-in, so the wear is larger. Such as the running-in period of a newly purchased mechanical vehicle. During this period, with the increase of time, the working surface of the parts gradually wears out, so that the fitting clearance between the parts reaches the initial clearance clearance. The second stage is the normal working stage of the parts. After the mating parts are run-in, the surface of the parts is smooth and smooth, and the mating clearance reaches the design standard. During the use of the machine, the amount of wear between the matching parts is very small, and the matching gap grows slowly. The third stage is the accident damage stage. During the use of the machine, due to the increase in the fit gap, impact load is generated, the lubrication conditions of the parts become worse, and the sharp increase in wear may damage the parts and cause mechanical accidents. Mechanical wear Mechanical wear is caused by the friction between the surfaces of the parts. Although the surface of the parts is machined, it is still impossible to be absolutely smooth. When the surfaces of the parts are in contact with each other, they are uneven and easy to embed in each other. When the parts move, the raised metal particles are constantly falling off. When the fit gap increases to a certain extent, the parts will increase due to the impact load, and the lubrication conditions will be destroyed and wear will continue to increase. For automotive parts and parts machining, PTJ Shop offers the highest degree of OEM service with a basis of 10+ years experience serving the automotive industry. Our automotive precision shop and experts deliver confidence. We have perfected the art of producing large component volumes with complete JIT reliability, backed by the quality and long-term reliability our customers expect.

Link to this article:The amount of wear between the mating parts is very small

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.:Cnc Machining,Thank

Comments

Popular posts from this blog

Drive the preferential presetting of the spring frame of the vehicle

The secondary spring system of the original electric locomotive consists of 4 sets of the same ordinary cylindrical compression springs. Its parameters are: spring material diameter d=48mm, maximum working circle diameter D=230mm, effective working circle number n=6.6, free height H0= 528mm, working height H=431mm. The characteristic curve of the spring is approximately straight, with stable stiffness and simple structure. However, the spring stiffness is mainly along the axial direction, and its transverse shear and bending stiffness is very poor, and its anti-resonance ability is poor. After the train speeds up, its snake-like movement and shaking phenomenon intensify. Therefore, it is necessary to improve the spring system of electric locomotives. Improvement of the spring system. The improved spring parameters and characteristics take into account the special position of the secondary spring (between the bogie and the car body) and specific functions (s...

How are the CNC Machining Manufacturers in Shenzhen? China Hardware Has Carried out Comprehensive Comparison with Multiple Dimensions in Various Regions

Keywords: Cnc Machining manufacturers,CNC Machining,How about Shenzhen CNC Machining manufacturers I'm not afraid of the quality of the product, I'm afraid to shop around. There is no contrast and no injury, this has been known to everyone since ancient times. For example, Shenzhen CNC Machining manufacturers, if you can find more Shenzhen CNC Machining manufacturers to compare their products, and compare the strengths of Shenzhen CNC Machining manufacturers, you will find that what you see with the naked eye is not all right, there may be some Unidentified objects participate in it, how do you compare them, and what aspects should you start with? Let's see how you do it. Everyone says to shop around. So, what is the comparison? Here is an explanation. Duowei Shenzhen is looking for suitable Shenzhen manufacturers for CNC Machining: 1. There are various qualification certificates: such as: business license, ISO, equipment distribution, enviro...

Hitachi LM213XB

# LM213XB Hitachi LM213XB New LM213XB KOE 5.8inch Panel 256×64 Monochrome B/L CPU, LM213XB pictures, LM213XB price, #LM213XB supplier ------------------------------------------------------------------- Email: sales@shunlongwei.com https://www.slw-ele.com/lm213xb.html ------------------------------------------------------------------- Panel Brand : HITACHI Panel Model : LM213XB Panel Type : STN- LCD , Panel  Panel Size : 5.8 inch Resolution : 256×64   Display Mode : STN, Yellow/Green (Positive), Reflective  Active Area : 143.31×35.79 mm Outline : 184×75×12 mm Display Colors : Monochrome     Signal Interface : 8-bit parallel , 20 pins   Input Voltage : 5.0V (Typ.)  ...