Skip to main content

How to solve the sensor system failure

If the signal from each input sensor or switch indicates that the engine cooling water temperature is lower than 24C, or the following situations occur, such as the throttle valve is suddenly opening and closing or even completely closed, the atmospheric pressure is lower than 66.66kPa, the car is braking, When the car is downshifting from fourth gear to second gear and upshifting from second gear to third gear, the lock-up clutch will not be locked.

In addition, because the failure of the input device (such as a sensor or switch) will endanger the function of the electronic control system, the system will automatically switch to the failure mode control state when an input sensor or switch fails. The lock of the lock release has occurred.

Similar to Chrysler’s approach, when the engine cooling water temperature rises above the prescribed lower limit (24°C), the throttle position sensor and the vehicle speed sensor will become the key input devices that determine whether the lock-up clutch is locked or not. At this time, the electronic control unit will make its control decision based on the two sets of throttle openings as a function of the vehicle speed curve.

If the car is driving in third gear, when the throttle opening is small, the lock-up clutch of the torque converter can be locked when the vehicle speed is only 43km/h: when the throttle opening is large, unless the driving speed is as high as 89km /h, otherwise the lock will not occur. When the car is running in fourth gear, if the throttle opening is small, the speed at which the lock-up clutch is locked is 56km/h; and when the throttle opening is large, unless the vehicle speed reaches 89km/h, it will lock. Will not happen. In addition, in the third gear state, the throttle opening corresponding to the lockup of the torque converter lock-up clutch is greater than 8% but less than 59% from the hot idle position: while in the fourth gear state, this The throttle opening is changed to greater than 5% and less than 45%. There is also a lock-up hysteresis zone.

Generally speaking, the conditions required for locking to occur are that the throttle opening is small and the vehicle speed is high. Once it has been locked, in order to improve the driving performance of the car, a larger one should be allowed before the lock is released. Throttle opening and lower vehicle speed appear.

The automotive parts and parts machining, PTJ Shop offers the highest degree of OEM service with a basis of 10+ years experience serving the automotive industry. Our automotive precision shop and experts deliver confidence. We have perfected the art of producing large component volumes with complete JIT reliability, backed by the quality and long-term reliability our customers expect.

Link to this article:How to solve the sensor system failure

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.:Cnc Machining,Thank

Comments

Popular posts from this blog

Drive the preferential presetting of the spring frame of the vehicle

The secondary spring system of the original electric locomotive consists of 4 sets of the same ordinary cylindrical compression springs. Its parameters are: spring material diameter d=48mm, maximum working circle diameter D=230mm, effective working circle number n=6.6, free height H0= 528mm, working height H=431mm. The characteristic curve of the spring is approximately straight, with stable stiffness and simple structure. However, the spring stiffness is mainly along the axial direction, and its transverse shear and bending stiffness is very poor, and its anti-resonance ability is poor. After the train speeds up, its snake-like movement and shaking phenomenon intensify. Therefore, it is necessary to improve the spring system of electric locomotives. Improvement of the spring system. The improved spring parameters and characteristics take into account the special position of the secondary spring (between the bogie and the car body) and specific functions (s...

How are the CNC Machining Manufacturers in Shenzhen? China Hardware Has Carried out Comprehensive Comparison with Multiple Dimensions in Various Regions

Keywords: Cnc Machining manufacturers,CNC Machining,How about Shenzhen CNC Machining manufacturers I'm not afraid of the quality of the product, I'm afraid to shop around. There is no contrast and no injury, this has been known to everyone since ancient times. For example, Shenzhen CNC Machining manufacturers, if you can find more Shenzhen CNC Machining manufacturers to compare their products, and compare the strengths of Shenzhen CNC Machining manufacturers, you will find that what you see with the naked eye is not all right, there may be some Unidentified objects participate in it, how do you compare them, and what aspects should you start with? Let's see how you do it. Everyone says to shop around. So, what is the comparison? Here is an explanation. Duowei Shenzhen is looking for suitable Shenzhen manufacturers for CNC Machining: 1. There are various qualification certificates: such as: business license, ISO, equipment distribution, enviro...

Hitachi LM213XB

# LM213XB Hitachi LM213XB New LM213XB KOE 5.8inch Panel 256×64 Monochrome B/L CPU, LM213XB pictures, LM213XB price, #LM213XB supplier ------------------------------------------------------------------- Email: sales@shunlongwei.com https://www.slw-ele.com/lm213xb.html ------------------------------------------------------------------- Panel Brand : HITACHI Panel Model : LM213XB Panel Type : STN- LCD , Panel  Panel Size : 5.8 inch Resolution : 256×64   Display Mode : STN, Yellow/Green (Positive), Reflective  Active Area : 143.31×35.79 mm Outline : 184×75×12 mm Display Colors : Monochrome     Signal Interface : 8-bit parallel , 20 pins   Input Voltage : 5.0V (Typ.)  ...