Skip to main content

Five parts of the car need to be replaced from time to time

1. Change the engine lubricating oil from time to time

Under normal circumstances, the manufacturers of naturally aspirated engine models sold in China will require users to change the lubricating oil when driving 5000 km-15,000 kilometers, while the supercharged engine models require replacement when driving 5000 kilometers. If the car does not drive too much Or it has been in a stopped state, and it is best to change the oil every six months. Of course, if your environment and oil quality are good, you can extend the oil change interval and time appropriately.

2, replace the oil filter from time to time

The function of the oil filter element is to filter impurities, so it must be replaced with the oil. If it is not replaced, the oil will not be filtered, which will cause the internal parts of the engine to wear out due to the impurities in the oil.

3. Replace the air filter from time to time

If the filter element is severely clogged, the air intake resistance will increase and the engine power will decrease. At the same time, due to the increase in air resistance, the amount of gasoline sucked in will also increase, resulting in an excessively rich mixture ratio, which will worsen the engine’s operating state, increase fuel consumption, and easily produce carbon deposits. Usually, you should get into the habit of checking the air filter element frequently.

4. Change the brake oil from time to time

One characteristic of brake fluid is that it absorbs water in the air, and the brake hydraulic system must allow the brake fluid to communicate with the atmosphere in order to function normally. Over time, the brake fluid will absorb water and turn into bubbles at high temperatures. If air bubbles appear in the battery, the braking performance will decrease. Therefore, the brake fluid should be replaced on time by checking its quality and performance according to the climate, operating environment, seasonal changes and working conditions.

General recommendation: Replace every two years or when driving 50,000 kilometers, and remember when selecting and replacing brake fluids: Do not mix different types and brands of brake fluids. Due to different formulas, mixing brake fluids will cause brake fluid indicators to drop.

5. Replace the antifreeze from time to time

If the antifreeze fluid is not changed for a long time, its anti-corrosion, anti-rust and anti-scaling functions will be reduced, which will cause the cooling system to malfunction or even rust. Generally speaking, the antifreeze is generally replaced every 1.5 to 2 years.

The above five items of car maintenance seem to cost a lot of money, but the money is issued to avoid major failures and bring us serious losses. Therefore, regular maintenance is necessary, and this is done so that it can better serve us.

The automotive parts and parts machining, PTJ Shop offers the highest degree of OEM service with a basis of 10+ years experience serving the automotive industry. Our automotive precision shop and experts deliver confidence. We have perfected the art of producing large component volumes with complete JIT reliability, backed by the quality and long-term reliability our customers expect.

Link to this article：Five parts of the car need to be replaced from time to time

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.：Cnc Machining，Thank

Comments

Post a Comment

Popular posts from this blog

Machining and welding process notes for TC4 titanium alloy parts

Common welding methods for titanium and titanium alloys are as follows: Argon arc welding, submerged arc welding, vacuum electron beam welding, etc. Tungsten argon arc welding is used for thicknesses of 3 mm or less, and argon arc welding is done for 3 mm or more. The purity of argon is over 99.99%, and the content of air and water vapor in argon is strictly controlled. Currently, for TC4 titanium alloys, argon arc welding, plasma arc welding are often used for welding, but both methods need to be filled with welding material. Limitations on shield gas, purity and effectiveness increase the oxygen content of the joint, reduce its strength and increase its post-weld deformation. Electron beam welding and laser beam welding are used. The following is a description of precision welding and precautions for TC4 titanium alloy. 1. Weld hole problem Table of Contents 1. Weld hole problem 2, internal quality of welded part 3. Weld depth and its variation 4, j...
Post a Comment
Read more

Introduction to the correct choice of lubricating oil in summer

In the summer heat, not only the human body will have various adverse reactions, but also the car. Today, I will share with you one of the things you need to pay attention to in summer-lubricants. The role of lubricating oil The heat generated by the friction between the various moving bearing surfaces of the engine is second only to the heat when the engine cylinder is burned, and the lubricating oil takes the heat away by pressure lubrication, thus ensuring the normal operation of the friction surface. The heated lubricating oil returns to the oil pan through the oil passage for cooling. In terms of the structure of the engine, the oil pan is located under the engine*, and it is exposed to the air. It is generally made of materials with good thermal conductivity, and the lubricating oil is air-cooled through it. The cooled lubricating oil is sent to the lubricated surface again. The viscosity of the lubricating oil is very important for protecting the en...
Post a Comment
Read more
The production process of KOVAR parts processing has a great relationship with the process, including the process environment elements and the optimization configuration elements of the process route. The process route process needs to be formulated by an experienced person. The following is a brief explanation of the process process. The formulation of the process route process: First, the geometric structure of the parts, the core parts of the accuracy index, the accuracy requirements, material characteristics, heat treatment requirements and performance requirements, etc. should be carefully analyzed, and then the blanks of the parts should be reasonably selected, the cnc machining china equipment should be used reasonably, and reasonable measures should be taken. Many process links such as stress process measures are reasonably configured. In the production organization process, the process is strictly implemented. During the process, strict inspection is performed. For general p...
Post a Comment
Read more