Skip to main content

Automobile automatic transmissions require more careful care and maintenance

The traffic conditions in the city are getting worse and worse. Stop-and-go in traffic jams is exhausting for owners of manual-shift cars. Therefore, the light and trouble-saving automatic transmission car has almost become the first dazzle of most urban residents. Although the automatic transmission car is easy to use, but because the automatic transmission system is a very sophisticated assembly, especially the manual automatic transmission Its structure is even more complicated. Therefore, once the automatic transmission fails, it is very troublesome and expensive to repair. In view of this, automatic gearboxes need more careful care and maintenance.

Regularly check the transmission oil

A kind of lubricating oil called ATF is injected into the automatic gearbox. In addition to lubricating and cooling down, its role is to transmit the power between the engine and the gearbox. The working temperature of ATF oil is generally around 120 degrees Celsius, so the quality of the oil is very high, and it must be kept clean.

Always check whether the automatic transmission oil level is normal. The inspection method of automatic transmission oil is different from that of engine oil. The engine oil is checked in a cold state, and the transmission oil needs to be preheated to about 50°C, and then the gear lever stays in each gear for 2 seconds. Put it in the parking block. At this time, the normal oil level of the oil dipstick should be between the highest and lowest lines. If it is not enough, add oil of the same quality in time.

In general, whether it is a manual gearbox or an automatic gearbox, it is recommended to change the automatic transmission oil every 12 months or 20,000 kilometers. Some models have instructions for 24 months or 40,000 kilometers. However, the above is only a general recommendation. Due to the special conditions of Beijing’s vehicles, heavy sandy weather, road congestion, and poor air quality, it is recommended that vehicles should be inspected regularly and replaced with ATF in time.

Change the gearbox oil correctly

Generally, when replacing the automatic transmission oil, the screw in the oil bottom of the automatic transmission is usually removed to leak the old oil and then add new oil, but this can only replace about 30% of the new oil and 70% of the old oil. Still remaining in the gearbox. If the oil is changed by removing the oil pan, the oil change rate can reach 70%, which can actually ensure the health of the gearbox. However, the current better method of oil change is dynamic oil change. Special gearbox cleaning equipment is used. During the operation of the gearbox, the old oil is fully circulated and drained before adding new gearbox oil to change the oil. The rate is as high as 90%.

GM, Toyota, Ford and other brands of automatic transmissions have different friction coefficients, so ATF oils are different and cannot be mixed. Mixed use of ATF will cause damage to the friction lining of the gearbox, slipping of the clutch and brake, etc., and in severe cases, the friction lining will be destroyed.

The automotive parts and parts machining, PTJ Shop offers the highest degree of OEM service with a basis of 10+ years experience serving the automotive industry. Our automotive precision shop and experts deliver confidence. We have perfected the art of producing large component volumes with complete JIT reliability, backed by the quality and long-term reliability our customers expect.

Link to this article：Automobile automatic transmissions require more careful care and maintenance

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.：Cnc Machining，Thank

Comments

Post a Comment

Popular posts from this blog

What are the characteristics of the CNC turning process?

What are the characteristics of the CNC turning process? Turning is a method of cutting the workpiece on the lathe by rotating the workpiece relative to the tool. Turning is the most basic and common cutting processing method. Most workpieces with revolving surfaces can be processed by turning methods, such as inner and outer cylindrical surfaces, inner and outer conical surfaces, end surfaces, grooves, threads, and rotary forming surfaces. Common lathes can be divided into horizontal lathes, floor lathes, vertical lathes, turret lathes and profiling lathes, and most of them are horizontal lathes.
1 comment
Read more

The Influence of CNC Turning and Milling Machining on Turning Efficiency

The cutting efficiency of CNC lathes will be affected by human factors, environmental factors and the machine tool itself. Let's talk about the influence of cutting amount and cutting tools on CNC lathe processing among many factors.   Reasonable cutting amount can improve the efficiency of CNC lathe. When the   laser  cutting  speed is increased by 10 times and the feed rate is increased by 20 times, far beyond the traditional cutting forbidden zone, the cutting mechanism has undergone a fundamental change.   The result of CNC turning  and milling combined processing is: the metal removal rate per unit power is increased by 30% to 40%, the cutting force is reduced by 30%, the cutting life of the tool is increased by 70%, and the cutting left on the workpiece is greatly reduced. Heat, cutting vibration almost disappeared; cutting processing has taken an essential leap. According to the current situation of CNC lathes, increase the feed per tooth, improve pr...
1 comment
Read more

Alternate vehicles, transportation equipment and field work machine oil in all seasons adapt to changes in temperature

  Foreign oil companies adopt tracking services for key users. Whenever the oil change period is approaching and users need to buy oil, they will test the oil for free in advance, issue an inspection report, and actively provide key users with a scientific basis for oil change. This kind of thoughtful service not only shortens the distance with users, but also improves the credibility of the brand. The alternation of the four seasons requires the oil used in vehicles, transportation equipment and field work tools to adapt to changes in temperature, especially in the north. Lubricants of different viscosity grades are usually replaced at the end of autumn and spring, thus forming a peak season for lubricating oil sales. Foreign oil companies attach great importance to the promotional activities in these two seasons. In the autumn, they launched low pour point, low viscosity grades of multi-grade antifreeze and antifreeze, and accompanied the promotion a...
Post a Comment
Read more