Skip to main content

The shell produces a downward thrust

The water pump housing of the riding motorcycle is installed in the front of the left axle box cover, while the water pump housing of the sitting motorcycle is actually installed in the front of the right axle box cover. When the impeller on the water pump shaft rotates, a vacuum is formed at the center of the impeller. The coolant from the hose under the radiator just leads to the center of the impeller and enters the pump. The impeller rotates with the coolant, and the coolant is thrown away due to the centrifugal effect of rotation. It is thrown to the outer edge of the impeller and has a certain pressure, and is transported to the water jacket of the cylinder under the guidance of the centrifugal guide groove at the outer edge of the impeller of the casing. When the temperature of the coolant is higher than the temperature of the coolant, the yellow wax in the inner cavity of the thermostat is heated to melt and become liquid, the yellow wax expands in volume, and the extruded rubber sleeve shrinks toward the center, thereby generating a pushing force on the lower end cone of the reverse push rod. The upper end is fixed, so the lower end cone of the reverse thrust rod produces a downward reverse thrust on the rubber sleeve and the shell, thereby compressing the spring to open the valve. At this time, the high temperature and cold cycle valve in the engine closes the large cycle valve and opens the shell. The rubber sleeve is yellow wax. . Thermostat The thermostat housing is generally installed at the outlet of the upper water jacket of the cylinder head, and the top leads to the right side of the radiator or the upper water tank. It is a switch or valve for the circulation route of the coolant in the cooling system. The upper bracket valve seat and the lower bracket are riveted into a whole. The cooling liquid of the radiator cover passes through the fully opened thermostat valve, flows from the top of the shell through the hose on the radiator to the radiator for cooling, and all the cooling liquid circulates between the radiator and the engine water jacket. When the temperature of the coolant is lower than that, the yellow wax in the thermostat gradually becomes solid, the volume is reduced, and the valve is seated and closed again under the action of the spring force. The radiator is composed of left and right (or upper and lower) water tanks and the radiator core. The radiator coolant flows from the right water tank through the radiator core, and then flows to the left pressure valve to open the water tank, which is called a cross-flow radiator. This kind of radiator is widely used in modern motorcycles, especially multi-cylinder engines. For automotive parts and parts machining, PTJ Shop offers the highest degree of OEM service with a basis of 10+ years experience serving the automotive industry. Our automotive precision shop and experts deliver confidence. We have perfected the art of producing large component volumes with complete JIT reliability, backed by the quality and long-term reliability our customers expect.

Link to this article：The shell produces a downward thrust

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.：Cnc Machining，Thank

Comments

Post a Comment

Popular posts from this blog

The Influence of CNC Turning and Milling Machining on Turning Efficiency

The cutting efficiency of CNC lathes will be affected by human factors, environmental factors and the machine tool itself. Let's talk about the influence of cutting amount and cutting tools on CNC lathe processing among many factors.   Reasonable cutting amount can improve the efficiency of CNC lathe. When the   laser  cutting  speed is increased by 10 times and the feed rate is increased by 20 times, far beyond the traditional cutting forbidden zone, the cutting mechanism has undergone a fundamental change.   The result of CNC turning  and milling combined processing is: the metal removal rate per unit power is increased by 30% to 40%, the cutting force is reduced by 30%, the cutting life of the tool is increased by 70%, and the cutting left on the workpiece is greatly reduced. Heat, cutting vibration almost disappeared; cutting processing has taken an essential leap. According to the current situation of CNC lathes, increase the feed per tooth, improve pr...
1 comment
Read more

What are the characteristics of the CNC turning process?

What are the characteristics of the CNC turning process? Turning is a method of cutting the workpiece on the lathe by rotating the workpiece relative to the tool. Turning is the most basic and common cutting processing method. Most workpieces with revolving surfaces can be processed by turning methods, such as inner and outer cylindrical surfaces, inner and outer conical surfaces, end surfaces, grooves, threads, and rotary forming surfaces. Common lathes can be divided into horizontal lathes, floor lathes, vertical lathes, turret lathes and profiling lathes, and most of them are horizontal lathes.
1 comment
Read more

Machining and welding process notes for TC4 titanium alloy parts

Common welding methods for titanium and titanium alloys are as follows: Argon arc welding, submerged arc welding, vacuum electron beam welding, etc. Tungsten argon arc welding is used for thicknesses of 3 mm or less, and argon arc welding is done for 3 mm or more. The purity of argon is over 99.99%, and the content of air and water vapor in argon is strictly controlled. Currently, for TC4 titanium alloys, argon arc welding, plasma arc welding are often used for welding, but both methods need to be filled with welding material. Limitations on shield gas, purity and effectiveness increase the oxygen content of the joint, reduce its strength and increase its post-weld deformation. Electron beam welding and laser beam welding are used. The following is a description of precision welding and precautions for TC4 titanium alloy. 1. Weld hole problem Table of Contents 1. Weld hole problem 2, internal quality of welded part 3. Weld depth and its variation 4, j...
Post a Comment
Read more