Skip to main content

AUO M190EG01 V1

AUO M190EG01 V1
#M190EG01 V1 AUO M190EG01 V1 New AUO 19inch LCM 1280×1024 270 1300:1 89/89/89/89 16.7M CCFL LVDS, M190EG01 V1 pictures, M190EG01 V1 price, #M190EG01 V1 supplier
-------------------------------------------------------------------
Email: sales@shunlongwei.com

-------------------------------------------------------------------
Manufacturer AUO
Model Name M190EG01 V1  
Screen Size 19.0 inch
Screen Type LCM ,   a-Si TFT-LCD
Pixel Number 1280(RGB)×1024   (SXGA)  86PPI
Arrangement RGB Vertical Stripe
Active Area(mm) 376.32 × 301.056 (H×V)
Outline(mm) 410.1 × 323.6 × 18.97 (H×V×D)
Bezel Area(mm) 380.32 × 305.06 (H×V)
Treatment Antiglare, Hard coating (3H)
Luminance 270 cd/m² (Typ.)
Contrast Ratio 1300 : 1 (Typ.) (TM)    
Viewing Angle 89/89/89/89 (Typ.)(CR≥10) Left / Right / Up / Down
Response 15/5 (Typ.)(Tr/Td); 8 (Typ.)(G to G) ms
Good View at Symmetry Work Mode P-MVA, Normally Black, Transmissive
Color Depth 16.7M   72% NTSC
Backlight 4 pcs CCFL , 50K hours , No Driver
Mass 2.80/3.00Kgs (Typ./Max.)
Used for Desktop Monitor Industrial
Refresh Rate 60Hz 
120Hz (60HZ Input) : Embedded MEMC Circuit
120Hz+120Hz : 120Hz Panel+120Hz Backlight
240Hz (60HZ Input) : Embedded MEMC Circuit
Touchscreen Without
Signal Type LVDS (2 ch, 8-bit) , 30 pins Connector
Voltage Supply 5.0V (Typ.) 
Max. Ratings Storage Temp.: -20 ~ 60 °C    Operating Temp.: 0 ~ 50 °C   
M190EG01 V1 inverter, M190EG01 V1 power supply, M190EG01 V1 electronic board, M190EG01 V1 VGA board, M190EG01 V1 touchscreen available.

Comments

Post a Comment

Popular posts from this blog

Drive the preferential presetting of the spring frame of the vehicle

The secondary spring system of the original electric locomotive consists of 4 sets of the same ordinary cylindrical compression springs. Its parameters are: spring material diameter d=48mm, maximum working circle diameter D=230mm, effective working circle number n=6.6, free height H0= 528mm, working height H=431mm. The characteristic curve of the spring is approximately straight, with stable stiffness and simple structure. However, the spring stiffness is mainly along the axial direction, and its transverse shear and bending stiffness is very poor, and its anti-resonance ability is poor. After the train speeds up, its snake-like movement and shaking phenomenon intensify. Therefore, it is necessary to improve the spring system of electric locomotives. Improvement of the spring system. The improved spring parameters and characteristics take into account the special position of the secondary spring (between the bogie and the car body) and specific functions (s...
Post a Comment
Read more

Mitsubishi RM100HA-20F

# RM100HA-20F Mitsubishi RM100HA-20F New IGBT: 100A1000V, RM100HA-20F pictures, RM100HA-20F price, #RM100HA-20F supplier ------------------------------------------------------------------- Email: sales@shunlongwei.com https://www.slw-ele.com/rm100ha-20f.html ------------------------------------------------------------------- rm100ha-20f Description rm100ha-20f is a DIODE RECTIFIER BRIDGE SINGLE.   Target Applications rm100ha-20f Free wheel use, Welders IGBT: 100A1000V
Post a Comment
Read more

Hydrostatic guideway of CNC machining lathe

The static pressure slide rail (TTW guide) of the CNC machining lathe transfers the oil with a certain pressure through the throttle to the oil cavity between the sliding surfaces of the slide rail (TTW guide) to form a pressure oil film to float the moving parts , Make the sliding rail (TTW guide) surface in a pure liquid friction state.   CNC machining General CNC machining usually refers to computer digital control precision machining, CNC machining lathe, CNC machining milling machine, CNC machining c17200   beryllium   copper   and milling machine, etc. The feed route of finishing is basically carried out along the part contour sequence. Therefore, the focus of determining the feed route is to determine the feed route of rough machining and idle stroke. In the numerical control processing, the control system issues instructions to make the tool perform various motions that meet the requirements, and the shape and size of the workpiece are expressed in the form o...
Post a Comment
Read more