Efficient Chips and the Thermal Cycle Failure Free SLC-package-technology This concept is convincing because it is based on a standardized package outline while also capable of delivering the highest power density, scalability by easy paralleling, low stray inductance, capability to operate with fast switching devices like SiC MOSFETs and having excellent current sharing balance. In combination with the latest 7th generation IGBT and Diode efficient chips and the thermal cycle failure free SLC-package-technology, the LV100 module provide the best overall performance. In the 1700V, a current rating of 1200A has been realized which represents an outstanding current density considering the compact package footprint of only 144x100mm².
NEXt Genaration IGBT
LV100 Internal Layout In high power IGBT modules, multiple chips are connected in a parallel configuration because IGBT chips sizes are limited and usually the rating maximum current is in a range of ~200A for IGBT chips with blocking voltages of 1200V or 1700V.
Achieving Homogeneous Loss and Heat Distribution Therefore, for the realization of an IGBT module with a current rating of 1200A or more, paralleling of at least six or more IGBT chips is required. While designing the layout, the current balancing between the chips connected in parallel has to be considered. Equally shared chip currents are required for achieving homogeneous loss and heat distribution. A non-homogeneous current distribution causes a certain chip to carry the highest current and this chip will experience the highest temperature which ultimately limits the performance and life-time of the total system.
Parasitic Impedances of the Connection The parasitic impedances of the connection to the individual chips significantly influence the current sharing between the chips operated in parallel. In case the parasitic inductances are not equally designed for all chips, a dynamic current imbalance during IGBT switching will occur. The module terminal arrangements and the chip positions are the major influencing factors for the parasitic impedances. To realize an equal impedance, the distances from the power terminals to all the chips have to be ideally the same.
This can be achieved by optimizing the terminal and chip arrangement so that it is perpendicular to the current flow as shown in figure 3 . In the ideal module concept, the commutation (indicated by the blue and red arrows) is only in Y-direction whereas the terminals and chips are orientated perpendicular in x-direction.
By this approach, equal parasitic impedances are achievable. This ideal concept was considered in the development of the LV100 layout and a homogenous current sharing, as shown in the simulation result in figure 4 was realized.
Conventional Modules The conventional modules available today in the field of high power industrial drives or converters for renewable energy usually have a terminal arrangement which is parallel to the chip arrangement and current flow. As a result of this conventional design, equal parasitic impedances was not be realizable and the resulting imbalance in the current sharing was an accepted feature of the conventional modules. For events such as load short circuits, due to the absence of the inductive coupling in the laminated busbars, the impact of the unequal stray inductances between different chips becomes significant for such conventional modules.
SiC Devices In case of fast switching semiconductor devices with high di/dt, the differences in parasitic stray inductances between the chips will influence the current sharing enormously. Therefore, if an Inverter designer considers changing to SiC devices in future, the LV100 package is the right choice since the layout concept is ready for SiC . As result, a potential future change from Si-IGBT to SiC-MOSFET devices is feasible with less changes and redesign efforts.
Thermal cycle failure-free package IGBT modules in high power industrial drive applications experience thermal cycling in case of fluctuating (or non-continuous) loads. Wind power converters are usually liquid-cooled with the cooler having a thermal time constant of a couple of seconds. As a result, the IGBT case temperature will respond rapidly to a temperature swing by changing of load conditions. That means on days with fluctuating wind conditions the IGBT module baseplate will experience many thermal cycles. Also photovoltaic inverters experience at minimum one huge thermal cycle per day. Considering an inverter life-time of 25 years, the IGBT module have to be capable to resist several thousand thermal cycles.
The thermal cycle capability of conventional industrial IGBT modules with conventional package structure (with several pieces of ceramicling substrates solder to copper baseplates), is limited. Hence thermal cycles have to be considered as lifetime limiting parameter during the converter design. To eliminate thermal cycling as lifetime limiting parameter, the SLC-Technology has been selected for the LV100 development for industrial application. As shown in figure 5, the conventional power module package structure is replaced by an IMB (Insulated Metal Baseplate) in combination with a direct potting resin.
The thermal expansion coefficient of the insulator and the potting resin are matched with each other (considering the thermal expansion of copper base- and pattern-layer. Due to this matching thermal expansion and the elimination of system solder layer, a thermal cycling failure free package structure has been realized .
7th gen 1700V IGBT chip-set The 7th gen IGBT and diode chips possess an optimized structure and are thinner than its predecessors. Additionally, the devices have been designed by selecting an appropriate trade-off between the DC performance and the switching performance .
NEXt Genaration IGBT
The inverter losses under typical application conditions for high power converters has been performed by Mitsubishi Electric Melcosim simulation software. In figure 6 the result and comparison of 1200A/1700V LV100 vs a conventional 1400A/1700V module from company A. It is noticeable that for a switching frequency of 500Hz the total losses are comparable. However, due to the appropriately selected trade-off in combination with the optimized chip structure, the diodes and the IGBTs indicate switching losses are significantly reduced.
The result is that for switching frequencies higher than 500Hz, the LV100 has significantly higher efficiency. For example, at a switching frequency of 5kHz the loss reduction is 39%. This loss reduction contributes to reducing the cost of the total inverter by reducing efforts for cooling and enabling to achieve higher power density of the system.
Conclusion A new high power IGBT module (LV100 for industrial) is under development, which has been optimized for the requirements of high power applications in the field of renewable energy converters, and industrial drives. The outline of the module housing is same as HVIGBT LV100 and in line with the new market defacto standard. The SLC-package-technology is thermal cycling failure free and improves the reliability of the system.
The 7th gen IGBT chip technology provides a significant reduction of switching losses and is beneficial considering a switching frequency from 500Hz onwards. The internal layout has a minimized stray inductance and ensures a homogenous current sharing between the chips. Therefore, it is feasible to use this layout with fast switching semiconductor. https://www.igbt.tech/
What are the characteristics of the CNC turning process? Turning is a method of cutting the workpiece on the lathe by rotating the workpiece relative to the tool. Turning is the most basic and common cutting processing method. Most workpieces with revolving surfaces can be processed by turning methods, such as inner and outer cylindrical surfaces, inner and outer conical surfaces, end surfaces, grooves, threads, and rotary forming surfaces. Common lathes can be divided into horizontal lathes, floor lathes, vertical lathes, turret lathes and profiling lathes, and most of them are horizontal lathes.
The cutting efficiency of CNC lathes will be affected by human factors, environmental factors and the machine tool itself. Let's talk about the influence of cutting amount and cutting tools on CNC lathe processing among many factors. Reasonable cutting amount can improve the efficiency of CNC lathe. When the laser cutting speed is increased by 10 times and the feed rate is increased by 20 times, far beyond the traditional cutting forbidden zone, the cutting mechanism has undergone a fundamental change. The result of CNC turning and milling combined processing is: the metal removal rate per unit power is increased by 30% to 40%, the cutting force is reduced by 30%, the cutting life of the tool is increased by 70%, and the cutting left on the workpiece is greatly reduced. Heat, cutting vibration almost disappeared; cutting processing has taken an essential leap. According to the current situation of CNC lathes, increase the feed per tooth, improve pr...
Foreign oil companies adopt tracking services for key users. Whenever the oil change period is approaching and users need to buy oil, they will test the oil for free in advance, issue an inspection report, and actively provide key users with a scientific basis for oil change. This kind of thoughtful service not only shortens the distance with users, but also improves the credibility of the brand. The alternation of the four seasons requires the oil used in vehicles, transportation equipment and field work tools to adapt to changes in temperature, especially in the north. Lubricants of different viscosity grades are usually replaced at the end of autumn and spring, thus forming a peak season for lubricating oil sales. Foreign oil companies attach great importance to the promotional activities in these two seasons. In the autumn, they launched low pour point, low viscosity grades of multi-grade antifreeze and antifreeze, and accompanied the promotion a...
Comments
Post a Comment